Enjoy Higher Performance In Your Everyday Communications – Now Available !

Attention IC-7410 Owners!
Download the latest firmware updates


Icom proudly announces the debut of the new HF/50MHz transceiver IC-7410. The IC-7410 has been designed as an HF/50MHz specialized rig with excellent performance and features in this category. The IC-7410 employs high grade DSP unit and double conversion super-heterodyne system developed from the latest technology used in our higher grade rigs such as the IC-7800/7700/7600 series. In addition, the IC-7410 comes with a built-in 15kHz 1st IF filter and can accept up to two optional filters (3kHz/6kHz). When used with these 1st IF filters, narrow mode signals such as the CW and SSB modes are protected from adjacent strong signals.

Read the QST Review of the IC-7410 here!

*Click the image to view the PDF review.
QST Product Review IC-7410 Amateur Radio

Major features

  • +30dBm 3rd order intercept point (in 14MHz band)
  • Double conversion superheterodyne system improves inband IMD characteristics
  • 32-bit floating point DSP unit
  • Built-in 15kHz first IF filter and optional 3kHz and 6kHz first IF filters
  • Large monochrome LCD display
  • ±0.5ppm frequency stability
  • Built-in simple band scope
  • Built-in automatic antenna tuner
  • All mode (SSB/CW/RTTY/AM/FM)
  • Optional RS-BA1 for IP remote control

dsp unitFaster DSP unit and in-house DSP expertise

The IC-7410 employs a much higher speed DSP unit compared to the IC-746PRO/7400's DSP unit. The AD/DA converter AK4620B allows for a high dynamic range and superior S/N ratio.

Icom has many years of DSP expertise, and has been key in development of the technology. The IC-7410 represents the latest in digital achievement and performance.

dsp unit and ad/da converter

double-conversion superheterodyne

Double-conversion superheterodyne

The IC-7410 employs a double conversion superheterodyne system which has an image rejection mixer for the 2nd mixer stage. When compared to a typical triple-conversion system, signal distortion is dramactically reduced.


+30dBm third-order intercept point (IP3)

third-order intercept pointIcom's analog RF circuit experience  combined with the latest DSP software technology results in +30dBm IP3 equivalent to the IC-7600. Even in tough RF conditions, such as interference by broadcast stations or strong neighboring ham stations, a weak signal can be clearly received by the IC-7410.

Three first IF filters (3/6/15kHz)*

The IC-7410 comes with a built-in 15kHz 1st IF filter and can accept up to two optional filters (3kHz FL-431 and 6kHz FL-430). By changing the firstif filterIF filter width according to the operating mode, the desired signal is protected from the influence of nearby strong stations. The 3kHz first IF filter is especially effective in the CW and SSB modes. (Fixed for 15kHz in FM mode.)
* in 14MHz 

High frequency stability

A high stability TCXO crystal oscillator provides ±0.5ppm of high frequency stability over a wide temperature range (0°C to +50°C). This allows for a long stable operating time in modes such as RTTY.

Large, multi-function LCD

multi-function lcdThe display increases in width from the IC-746PRO/7400. The large multi-function LCD shows frequency, 9-character channel name, channel number, multi functional meter (includes S-meter, RF output, SWR and ALC level). The dot-matrix portion of the LCD shows the following items:

  • Channel name
  • Band scope
  • Memory keyer contents
  • Function key assignment
  • RTTY decoder screen
  • Graphical SWR scale

Simple band scope

The built-in simple band scope shows the band condition at a glance and is handy for searching for active stations.

RTTY demodulator and decoder

The built-in RTTY demodulator and decoder allows you to instantly read an RTTY message on the display. No external units or PC required. The built-in tuning indicator visually helps in critical tuning.

Ample CW functions

All of the following CW capabilities are included in the IC-7410

  • Large CW PITCH knob and independent BK-IN (break-in) delay knob improve operating efficiency
  • CW wave form controlled by the DSP
  • 4 keyer channels with 70 characters of transmit memory per channel
  • Multi-function electronic keyer with adjustable keying speed from 6-48 wpm, dot-dash ratio from 1:1:2.8 to 1:1:4.5 and paddle polarity
  • Bug keyer and full break-in function
  • Continuously adjustable CW pitch control from 300-900Hz
  • Double key jacks (front and rear panels)
  • CW reverse

Built-in antenna tuner

The internal antenna tuner covers from 1.8MHz to 54MHz and automatically tunes for low SWR. Variable capacitors provide higher accuracy than a typical mechanical relay tuner. Once you transmit on a frequency, the tuner can instantly retune the frequency using its built-in memory.USB connector

USB connector for PC control

The IC-7410 has a standard type B USB connector and can be connected to a PC. Modulation input, audio output, RTTY demodulator output and CI-V command can be controlled via the USB cable. Also, the conventional CI-V remote control jack is built-in to the IC-7410.

Download the USB Driver

large heat sinkLarge heat sink

When compared to the IC-746PRO/7400, the IC-7410's large heat sink improves heat dissipation. Even during long hours of heavy-duty cycle operation, the IC-7410 provides stable output power.

Optional RS-BA1 IP remote control software

The optional RS-BA1 allows you to use the IC-7410 from another room using your home network or even from a remote location over the Internet. Most settings such as filter width, AGC constant, etc., can be controlled from your PC.

RSBA1IP software

Other outstanding features

  • Built-in voice synthesizer announces operating frequency, mode and S-meter level
  • User programmable band edge beep (can be disabled)
  • VSC (Voice Squelch Control) function
  • RF speech compressor
  • Microphone equalizer and adjustable transmit bandwidth
  • Two preamplifier types: Preamp 1: Increases low level signal improving intermodulation characteristics, Preamp 2: High gain preamplifier
  • 20dB built-in attenuator
  • Audio equalizer function
  • CTCSS and DTCS tone encoder and decoder
  • Triple band stacking register
  • Quick split function and frequency lock function
  • RIT and ΔTx variable up to ±9.999kHz
  • SSB/CW synchronous tuning automatically shifts the carrier point when switching between CW and LSB/USB modes
  • 1Hz pitch tuning steps
  • Program scan, memory scan, select memory scan, mode select scan and Δf scan
  • Automatic tuning steps
  • AH-4 control circuit
  • Large independent MIC/RF power and Notch knobs

Rear panel

  1. Tuner Socket
  2. DC Power Socket
  3. Ground Terminal
  4. Antenna Connectors
  5. Key Jack
  6. ALC Input Jack
  7. Send Control Jack
  8. Accessory Socket
  9. CI-V Remote Control Jack
  10. USB Connector
  11. External Speaker Jack

IC7410 back view


Frequency coverage (U.S. version)

*Frequency coverage depends on version. Some frequency bands are not guaranteed.

1.800-1.999MHz 3.500-3.9999MHz
5.255-5.405MHz * 7.000-7.300MHz
10.100-10.150MHz 14.000-14.350MHz
18.068-18.168MHz 21.000-21.450MHz
24.890-24.999MHz 28.000-29.700MHz
Number of memory channels 101 channels
(99 regular Ch, 2 scan edges)
Power supply requirement 13.8V DC ±15%
Frequency stability Less than ±0.5ppm (0°C to +50°)
Operating temperature range

0°C to +50°C;

32°F to +122°F

Current drain (at 13.8V DC)
TX Max. power 23A
RX Max. audio 3.0A
  Stand-by 2.2A
Antenna connector SO-239 (50Ω) × 2
Dimensions (WxHxD)

315 × 116 × 343 mm;

12.4 × 4.57 × 13.5 in

Weight 10.2kg; 22.5lb (approx.)
Modulation system


Digital PSN modulation

Digital low power modulation

Digital phase modulation

Output power SSB, CW, RTTY, FM: 2-100W
AM: 2-27W
Spurious emissions (unwanted emission)
Less than –50dB
Less than –63dB
Carrier suppression More than 40dB
Unwanted sideband More than 55dB
Microphone connector 8-pin modular (600Ω)
Intermediate frequencies 64.455MHz, 36kHz

SSB, CW (10dB S/N)

AM (10dB S/N)

*1Preamp 1 ON
*2Preamp 2 ON



0.16μV typ. 1

0.13μV typ. *2


12.6μV typ. *1

2.0μV typ. *1

1.6μV typ. *2


0.50μV typ. *1

0.32μV typ. *2



Squelch sensitivity 0.25μV typ. (at 12dB SINAD)

(BW: 2.4Hz, sharp)
(BW: 500Hz, sharp)
RTTY (BW: 350Hz sharp)
AM (BW: 6kHz)
FM (BW: 15kHz)  


More than 2.4kHz/–6dB

Less than 3.4kHz/–40dB

More than 500Hz/–6dB

Less than 700Hz/–40dB

More than 500Hz/–6dB

Less than 800Hz/–40dB

More than 6.0kHz/–6dB

Less than 10.0kHz/–40dB

More than 12.0kHz/–6dB

Less than 22.0kHz/–40dB

Spurious and image rejection More than 70dB
RIT variable range ±9.999kHz
PHONES connector 3-conductor 3.5 (d) mm (18 in.)
Audio output power 
(at 13.8V DC)
More than 2.0W at 10% distortion with an 8Ω load
External speaker connector 2-conductor 3.5 (d) mm (14″)/8Ω
Antenna Tuner

Matching range

HF bands

50MHz band

*1 VSWR: Less than 1:3


16.7Ω to 150Ω unbalanced*1

20Ω to 125Ω unbalanced*2

*2 VSWR Less than 1:2.5

Minimum operating power

HF bands

50MHz band




Tuning quality

VSWR Less than 1:1.5

Insertion loss
Other band (except for 1.8MHz)
(Matched at 100W output)
Less than 1.2dB
Less than 1.0dB

Measurements made in accordance with EIA/TIA-603-A. Compatibility of functions for use with a telephone line may not work in some countries. All stated specifications are subject to change without notice or obligation.


Write a review

Please login or register to review

IC-7410 HF/50MHz Transceiver

  • Brands Icom
  • Product Code: IC-7410
  • Availability: In Stock
  • Call for Price

Tags: icom ic-7410, ic-7410, mobile radio, base station radio, hf/50mhz transceiver, hf